The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
What are your ideas with regards to Installing A Bathtub?
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Setting up a tub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately challenging project. If the old bathtub is conveniently easily accessible, the job can move speedily; if you need to open a wall to get rid of the old bathtub as well as place the brand-new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the new one. See to it you have actually qualified yourself for the task and fit attempting it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will certainly assist you set up a brand-new bath tub in your restroom if you have already bought a new tub and don't require to transform the setup of your previous water pipelines.
Your devices as well as material list need to make up the following:
Planning for the Installment
To start with, the sustaining frame supplied with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to prevent strain on the tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of removing the existing taps can be quite problematic due to the limited access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the bath tub in the called for placement. The wood boards are useful in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level as well as readjusting the feet on the bathtub till the spirit level reviews degree.
To install faucets, fit all-time low of the furthest versatile tap adapter to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the supply of water and also inspect all joints as well as new pipework for leakages and tighten them if essential. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bathtub has been utilized at the very least once as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washers are in location between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type must be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes and cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the movement experienced when the bathtub is in use. The sealer can break rather very early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily offered on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were brought to that editorial on How to Install a Bathtub from a friend on our other web blog. If you enjoyed reading our page plz remember to share it. I truly appreciate reading our article about Installing A Bathtub.
For fast relief, call! Report this page